Stamping parts manufacturer to interpret considerations about stamping parts

Stamping parts manufacturer to interpret considerations about stamping parts

Stamping parts and castings, forgings, fights has the characteristic of thin, uniform, light and strong.Stamping can make this a master diameter is difficult to manufacture with enhanced, rib flanging, front, or artifacts, in order to improve its stiffness.Rejected due to the rough mould, workpiece precision can reach micron grade, and high precision, specification is consistent, can punching a hole nest, convex sets, etc.In the actual production, commonly used to approximate the manufacturability of stamping process test, such as deep drawing performance test, bulging performance test and other test materials stamping performance, to ensure the quality of the finished product and high qualified rate.

1. All the tools after use and return to the toolbox, cannot put on the machine, to avoid tool slide hurt people.

2. High impact after adjusted the machine, after normal stamping, close the soundproof box (except 8065 border edge packaging products).

3. The semi-automatic and manual punch press brake switch must be installed with both hands, it is forbidden to start switch pedal or one hand press.

4. The technician mode on the machine, can only be a person debugging, don't two people to debug.

5. The technician machine feed, only in the machine, not less than 1 m distance.

6. When frame mode must lock screw, 4 hours to check whether the screw is loose.

7. Continuous punching, employees can't punch within 1 m take products by hand.

8. Production operator, repair mode operation are strictly forbidden to handle knob stretch into the mould.

9. The machine is not production, to cut off the power supply in time.

10. Small workpieces, want to use special tools, may not be directly with the hand feeding or pick-up.

11. Producers to stand properly, hand and head should keep a certain distance with punching machine, and watch the punch movement, it is strictly prohibited to chat with other people.

12. Pay attention to drag the mould to prevent falling on the ground (to put the flat car in minimum to just die).

13. Operators when installing a suction fan, it is strictly prohibited to hand to clean waste on the motor.

14. It is forbidden to wear slippers at work, in order to prevent mould workshop, such as iron on foot.Monitor, fitter, repair mold engineer must wear labor insurance shoes at work;

15. Male workers are strictly forbidden to have long hair, long hair female workers to set up, in order to avoid long hair in the flywheel.

16. White electric oil, alcohol, cleaning agents and other oils should pay attention to fire prevention.

17. Materials, waste, and mold the need to wear gloves when using the homework, so as not to scratch the hand.

18. When there is oil must be clear in time, in order to prevent slippery wrestling.When the mold problems in the process of production does not need to discharge mode, directly on the machine maintenance, must first turn off the power supply and hang up on the power supply box injection molding are signs to repair mold maintenance.

19. Drilling and milling machine, gloves are forbidden;When using grinding machine to wearing surgical masks and eye shield, protect yourself.

20. It is strictly prohibited to air pressure gun aimed at one blow, easy to hurt the eyes.

21. It is strictly prohibited to the electrician personnel and maintenance of electrical machines.

22. Work, first check whether there is any abnormal on equipment operation, such as single, even not clear, the operation is ineffective or electrical failure, to immediately stop looking for technician on duty to deal with in a timely manner.

23. Operators need to wear ear plugs.

24. When he found the machine abnormal switch off the power supply first, then call the technician on duty in time, cannot do STH without authorization.

25. The new employee the first day at work, the team leader must be good to his safety operation specification, the first week to learn every day a safety operation procedures.

26. The machine, be sure to dispatch the machine to the single action, it is forbidden to play moving strip.

27. Under the switch can't store any flammable and explosive.

Chase chase 28. Operators are strictly prohibited in the workplace, in order to avoid the wrestling, down products, or hurt yourself.

29. When the mold problems in the process of production does not need to discharge mode, directly on the machine maintenance, must first turn off the power supply and hang up on the power supply box injection molding are signs to repair mold maintenance.

30. In small punch (10 t) are installed on the mould, to loosen the guide rail locking device, install the lower die, and then adjust the guide rail travel, until it meets the requirements and locked tightly solid device, the other in a high impact on die, must hit single stroke and lock on the mold after the mold after the hydraulic clamping lock, again for a check-up before production.,

31. Press foot switch is strictly prohibited, the machine comes with all down.

32. Should wear gloves when pressing plate, concentration, otherwise the injured hand.

33. According to the equipment point check card equipment check check content, pay special attention to punch guidance and brake equipment operation is normal, single and even the impact and function.

34. Cut off power supply, cleaning, scrubbing and working mesa, remove the mold maintenance warehouse, a weekly regularly check the oil lubrication system.

35. Clean, check the equipment, it must be cut off the power supply after the operation.

36. The discharge or hand took the embryo of a single to send, must use the special tool (pliers, hook), it is strictly prohibited to unarmed, take the embryo.Single switch to hand injury, to double the switch.The machine can't leak, otherwise you will fall down.The power supply not exposed, dangerous.

Dalian stampingManufacturer to design and productionStamping dieSimple, forging die, injection mold, has a complete and scientific quality management system.Welcome friends from all walks of life come to visit, guidance and business negotiation.